Page (551-01)

Available in PVC-PPH, PPH, PVDF and stainless steel 316 L 1 or 2 bi-stable change over contacts Small dimensions Lightly affected by specific weight variations 4-20 mA continuous transmitter (option RTM MNR6) • Versions: PVC, PPH, PVDF or AISI 316 •...

Created on 10/10/2006 16:50 and updated on 11/12/2019 13:35

Page (250-02)

- Protection of Reed contact - Outputs: 2 change over contacts, voltage free; 5A / 250 V AC / 500 VA - Status relay display - Regulation between two trigger points - Adjustable time delay

Created on 13/06/2007 10:38 and updated on 10/12/2019 14:03

Page (544-06)

For all electrical conductive liquids Suitable for level or leakage detection Adjustable sensitivity and timer, selection of action mode Self diagnostic with instant alarm (LED) for: Short circuit on the loop detection, Loop detection cable break off...

Created on 26/01/2009 14:13 and updated on 10/04/2018 14:08

Page (193-13)

Opened cell, 3 electrodes For industrial hot water, drinkable water, cooling water, process water Without diaphragm Range: 0.01 to 5 ppm Output signal: 4-20 mA Pressure limit: 8 bar Temperature limit: 5...70 °C • For hot sanitary water, drinkable...

Created on 25/11/2010 18:16 and updated on 04/12/2019 16:31

Starting Up Notice (520-03)

Created on 03/02/2012 12:23 and updated on 10/04/2018 15:35

Page (560-03)

• Version ATEX or complying to Pressure Equipment Directive • Direct reading on two-color ruler • Temperature up to 450 °C • Pressure up to 250 bar • Options: Level switches, Analogue signal transmitter, graduated ruler in %

Created on 11/12/2019 13:43 and updated on 11/12/2019 13:46

Starting Up Notice (232-03)

Created on 28/06/2007 15:54 and updated on 10/04/2018 15:20

Page (592-03)

Convenient for level controls on non-pressurised tank 4 switching points, adjustable over all the measuring range Convenient for aggressive and loaded fluids even viscous or / and sticky fluids Range: up to 10 m Water Column Reliable, without mobile...

Created on 19/11/2009 16:36 and updated on 10/04/2018 14:22

Starting Up Notice (193-04)

Created on 22/12/2010 14:03 and updated on 10/04/2018 15:25

Page (598-01)

• Height range 0.15 to 18 m, for liquids • Non-contact level measurement • HART® 7 protocole • Output signal 4-20 mA • IP 68 (allows accidental immersion)

Created on 11/12/2019 16:17 and updated on 11/12/2019 16:29

Starting Up Notice (289-01)

Created on 06/09/2007 09:54 and updated on 10/04/2018 15:22

News ()

BAMOBUL is designed for a reliable and accurate measurement The bubbling measuring method is a non-age technique. It is still today, a serious alternative to ultra sonic transmitter, offering a trouble free use with foaming process and a long-term high...

Created on 21/12/2009 17:35 and updated on 10/04/2018 16:23

Page (523-01)

For use in drinkable water , Food industry applications ACS Certificate = sanitary certification For use in drinkable water Food industry applications Built-in ballast Standard cable lengths 5, 10 and 20 m ACS Certificate = sanitary certification

Created on 07/07/2011 09:49 and updated on 10/04/2018 14:01

Page (140-02)

In-line electrode holder for pH and ORP electrodes PVC material Various process connections available • Holder for 1 electrode • Construction: in PVC • Spigot ends Ø 25 mm for solvent welding

Created on 08/10/2006 23:54 and updated on 04/12/2019 11:27

Starting Up Notice (555-01)

Created on 27/12/2007 16:44 and updated on 10/04/2018 15:42

News ()

We shall be exhibiting our productsin Munich at IFAT 2010, the world's leading trade fair for water, sewage, waste and raw materials management. September 13-17, 2010 - New Munich trade fair centre.

Created on 26/04/2010 11:43 and updated on 10/04/2018 16:19

Page (913-05)

ND 10 to ND 50 In-line pattern Pneumatic actuator Single or double acting, Position index Status NC or NO

Created on 08/12/2011 10:03 and updated on 10/04/2018 14:39

Page (194-06)

• Disinfectant measurements with auto-cleaning of sensor • 1 Input for CCK sensor • 1 Relay output • 1 Input for flow controller • OPTIONS: PID with 2 relays, 1 or 2 Analogue outputs 4-20 mA RS485 Interface (Modbus)

Created on 10/12/2019 12:47 and updated on 10/12/2019 12:49

Page (765-01)

Designed for agressive fluids Direct reading indicator From ND 50 up to ND 200 pipes Scale amplification from 2 to 10. Mounting in all positions Standardized with NF X 10-102 Norm Accuracy: ±2,5 % full scale Option: Electrical switch counter

Created on 09/10/2006 16:55 and updated on 10/04/2018 14:30

Starting Up Notice (192-02)

Created on 26/04/2007 11:12 and updated on 10/04/2018 15:24

Page (544-03)

LISA system or “ Liquid Intrusion Safe Alarming”, is designed for alarming as soon as humidity or a drop of water is detected on a ribbon like sensor. The fail safe alarming system LISA includes, as a minimum, one ribbon sensor or one-point...

Created on 23/10/2008 10:25 and updated on 11/12/2019 13:28

Page (193-95)

For sanitary, drinkable, cooling, water processed Dedicated holder for up to 5 sensors: Amperometric sensors, pH and ORP electrodes Flow limit controller, flow rate adjustment Stainless steel pin as liquid reference potential Outlet valve for sampling...

Created on 27/09/2010 17:11 and updated on 04/12/2019 17:19

Starting Up Notice (913-03)

Created on 12/12/2011 17:27 and updated on 10/04/2018 16:02

Page (364-04)

• Color touch screen • Measuring range, 4 scales: 0- 2 mS/cm up to 0 - 2000 mS/cm • Automatic temperature compensation • 2 Outputs 0/4-20mA • 4 Relays (Thresholds, alarm and/or regulation) • OPTIONS : RS 422 /J-BUS + LOGGER Extension...

Created on 10/12/2019 15:38 and updated on 10/12/2019 15:40

Page (585-01)

High power switching Reverse and bi-stable switch IP 65 housing • High switching power • Bistable switch • Protection: IP 65

Created on 10/10/2006 17:10 and updated on 11/12/2019 15:31

Page (542-02)

For well and bore-hole Compactness Material: Stainless steel • Compact electrodes • All stainless steel • For conductive liquids • Supplied with or without cable

Created on 13/06/2007 14:15 and updated on 11/12/2019 13:23

Starting Up Notice (544-06)

Created on 04/02/2009 18:25 and updated on 10/04/2018 15:40

Page (193-25)

For swimming pool water, drinkable water, cooling water, process water Range: from 0.001 up to 100.0 g/L Output signal: 4-20 mA Sensor affords surfactants Pressure limit: 1 bar as a maximum Unnecessary zero adjustment

Created on 26/11/2010 16:34 and updated on 10/04/2018 13:42

Starting Up Notice (520-01)

Created on 21/02/2012 13:11 and updated on 10/04/2018 15:35

Page (570-01)

• Direct reading on the tank • Height from 300 up to 2000 mm • Materials: Glass and brass • Seals: Silicon rubber • Option: Adjustable level contacts

Created on 11/12/2019 13:47 and updated on 11/12/2019 13:50

Page (222-02)

Inputs: 4-20 mA, 0-10 mA, 0-10 V, 1-5 V  Easy configuration  Display 5 digits  Housing 48 x 96 mm  Front IP65  Main power 95…265 V AC  Integrated sensor supply Min. / Max. values in memory  Programmable ramp: 9 segments

Created on 29/06/2007 11:54 and updated on 10/04/2018 16:31

Starting Up Notice (592-03)

Created on 19/11/2009 16:47 and updated on 10/04/2018 15:51

Starting Up Notice (193-05)

Created on 27/12/2010 15:15 and updated on 10/04/2018 15:25

Page (599-02)

• Ultrasonic probe • Level monitoring of sludge in sedimentation tanks • Advanced algorithm • Output 4-20 mA: representative of sludge level • Cleaning with compressed air • User-friendly menu

Created on 11/12/2019 16:31 and updated on 11/12/2019 16:34

Starting Up Notice (586-01)

Created on 14/09/2007 10:11 and updated on 10/04/2018 15:50

News ()

The software dedicated to the data logger BAMOPHOX is yet downloadable. Among new details, the inductive conductivity metre BAMOPHOX 322 TOR is included. Downloading: from the instructions manual page BAMOPHOX 106

Created on 21/12/2009 17:39 and updated on 10/04/2018 16:23

Page (913-01)

ND 10 to ND 100 In-line pattern Pneumatic actuator Single or double acting,  Position index Status NC or NO Standard compatibility: NAMUR VDI/VDE 3845 and ISO 5211 OPTIONS: Limit switch box Pilot valve

Created on 07/07/2011 13:07 and updated on 10/04/2018 14:38

Page (107-01)

• Color touch screen • 2 existing scales: 0... 14 pH or ±1000 mV • Temperature compensation: Automatic or manual • 2 outputs 0/4-20mA (pH and T °C) • 4 relays (Thresholds, alarm and/or regulation) • Options: RS 422 /J-BUS + LOGGER...

Created on 04/12/2019 10:33 and updated on 04/12/2019 10:36

Page (130-01)

Electrode holder and protection Easy calibration: buffer flask grips on Flange or PE collar fitting For any KCl gel type electrodes For PG 13.5 electrode threaded connection PVC, PPH or stainless steel construction Wire outlet through a PG 9 •...

Created on 09/10/2006 00:07 and updated on 04/12/2019 10:44

Starting Up Notice (555-02)

Created on 28/12/2007 13:59 and updated on 10/04/2018 15:42

Starting Up Notice (531-02)

Created on 06/05/2010 17:53 and updated on 10/04/2018 15:38

Page (913-06)

ND 65 to ND 200 In-line pattern Pneumatic actuator Single or double acting, Position index Status NC or NO Standard compatibility: NAMUR VDI/VDE 3845 and ISO 5211 OPTIONS Limit switch box Pilot valve

Created on 08/12/2011 10:13 and updated on 10/04/2018 14:40

Page (206-01)

• Wall mount box IP 55 • Dial 72 x 72 • 1 Analogue input • 1 Analogue output 0/4-20 mA • 2 Relay outputs

Created on 10/12/2019 12:52 and updated on 10/12/2019 12:59

Page (755-03)

Compact level transmitter Measuring height up to 6 m  Dead zone of 25 cm Adjustable range for the 4-20 mA output signal Programmable relay output (autodiagnostic or alarm)

Created on 09/10/2006 17:08 and updated on 10/04/2018 14:27

Page (450-02)

Alphanumeric back lighted LCD display Friendly using menu Scales: 0...100% or mg/L through configuration Temperature compensation: automatic or manual 2 analogical outputs 0/4-20mA galvanic insulated 3 independent relay outputs (N.O. contacts) 1 alarm...

Created on 10/05/2007 13:40 and updated on 10/04/2018 13:58

Starting Up Notice (583-01)

Created on 06/11/2008 18:42 and updated on 10/04/2018 15:47

Page (194-01)

Amperometric signal monitor Parameters according to the sensor in use: Free chlorine, Total chlorine, Chlorine dioxide, Ozone, Hydrogen peroxide, Peracetic acid Alphanumeric back lighted LCD display Friendly using menu 1 sensor input (4-20 mA or 0/-2...

Created on 27/09/2010 17:18 and updated on 10/04/2018 13:44

Starting Up Notice (913-04)

Created on 12/12/2011 17:30 and updated on 10/04/2018 16:03

Page (364-05)

- Measuring range from 10 μS/cm up to 2000 mS/cm - Construction: PEEK - Wide chemical compatibility - Temperature max. 125 °C - Low fouling probe - Built-in Pt100 sensor

Created on 10/12/2019 15:41 and updated on 10/12/2019 15:43

Starting Up Notice (450-02)

Created on 14/06/2007 11:35 and updated on 10/04/2018 15:33

Page (531-01)

Designed for the monitoring of hydrocarbon fluids separators, the converter NivOil® may be connected to 1, 2, or 3 sensors. The 3 sensors may be connected to any input. Hydrocarbon fluid layer thickness sensor to detect when the maximum thickness...

Created on 12/02/2009 13:51 and updated on 10/04/2018 14:02

Starting Up Notice (812-04)

Created on 26/11/2010 16:59 and updated on 10/04/2018 15:58

Starting Up Notice (914-02)

Created on 28/03/2012 16:28 and updated on 10/04/2018 16:07

Page (572-01)

• Direct reading on site • Measuring tube O.D. 63 mm • Wet parts: PVC and PPH • Stop valves, included • Options: Level switches, graduated ruler

Created on 11/12/2019 13:58 and updated on 11/12/2019 14:01

Starting Up Notice (410-01)

Created on 30/07/2007 16:51 and updated on 10/04/2018 15:31

Starting Up Notice (193-06)

Created on 27/12/2010 15:18 and updated on 10/04/2018 15:26

Page (613-01)

• Plastic probe • Materials: PVC, PP, PVDF • Sensor: Pt 100 Ω at 0 °C • Range: from -20 °C up to 140 °C

Created on 11/12/2019 16:45 and updated on 11/12/2019 16:46

Category ()

Created on 28/09/2006 22:50 and updated on 27/03/2018 16:27

Starting Up Notice (319-02)

Created on 17/09/2007 17:38 and updated on 10/04/2018 15:28

News ()

It was once more a successful exhibition "Environmental solutions" with 120000 visitors for 2560 exhibitors. Our booth BAMO-IER in the middle of numerous and talented manufacturers received congratulations from them as well as from visitors. The 2/3 of...

Created on 21/12/2009 17:45 and updated on 10/04/2018 16:22

Starting Up Notice (913-01)

Created on 07/07/2011 14:34 and updated on 10/04/2018 16:01

Page (130-02)

• Protective holder • Built-in temperature sensor Pt100 • Simplified calibration routine • For 1 electrode (PG 13.5 sealing) • Adjustable immersion depth • Fastening by flange or collar • PVC construction

Created on 04/12/2019 10:45 and updated on 04/12/2019 10:51

Page (135-01)

Electrodes holder and protection  2 or 3 electrodes, thread PG 13.5  PVC or PPH construction  Flange or PE collar fitting  Wire outlet through a cable gland  Easy mounting on site • Electrode holder and protector • Easy calibration routine •...

Created on 09/10/2006 00:16 and updated on 04/12/2019 11:10

Starting Up Notice (555-04)

Created on 28/12/2007 15:31 and updated on 10/04/2018 15:43

Starting Up Notice (531-03)

Created on 06/05/2010 17:57 and updated on 10/04/2018 15:38

Page (913-07)

ND 10 to ND 100 In-line pattern Pneumatic actuator Single or double acting, Position index Status NC or NO Standard compatibility: NAMUR VDI/VDE 3845 and ISO 5211  OPTIONS Limit switch box Pilot valve

Created on 08/12/2011 14:15 and updated on 10/04/2018 14:40

Page (212-02)

• 3.5'' TFT color display, 320x240 resolution • 4 Inputs: TC, RTD, mA, mV and V • 1 Logic data input / output • 2 potential free contact Inputs • 4 Relay outputs • 14 Virtual channels: Calculations, totalisers, counters ... • Modbus Slave...

Created on 10/12/2019 13:02 and updated on 10/12/2019 13:06

Page (755-02)

Overflow weir Standard: ISO 1438/1-1980 Measuring range: 1 m 3 /h to 400 m 3 /h V-angle from 20° to 90° Materials: PVC or PE Flow rate from 1 m3/h to 400 m3/h  V profile, angle 20°, 30°, 45°, 60° and 90°  Manufactured within drawings  Ready...

Created on 09/10/2006 17:19 and updated on 10/04/2018 14:27

Page (106-02)

For pH or ORP (mV) process operation Up to 4 regulation stages Scales: 0-14 pH and ± 1000 mV Temperature compensation: Manual from menu configuration Automatic with a Pt 100 Ohm 2 analog outputs as 0/4-20 mA, galvanic insulated 4 relay outputs: S1 /...

Created on 19/11/2008 09:49 and updated on 10/04/2018 11:56

Starting Up Notice (913-05)

Created on 12/12/2011 17:33 and updated on 10/04/2018 16:03

Page (448-02)

• Measuring scales: 0.50 to 50 FNU 50 to 1000 FNU • Easy to use • Supplied ready-to-use with a rigid case

Created on 10/12/2019 16:02 and updated on 10/12/2019 16:08

Page (141-01)

• On-line holders for 1 electrode • For full piping • Materials: PPH or PVDF • Mounting: screw fitting 3/4" G • Version for inserting and removing the electrode (PG 13.5) with full pipe

Created on 15/06/2007 14:35 and updated on 04/12/2019 11:34

Page (582-01)

Stainless steel Cat & Mouse Level indicator with metallic parts Wide scale Graduated in %, m3, L Long height possible Protected pulleys with a no jump system Sections of 1500 mm, adjustable total length • Metallic level indicator • Height up...

Created on 12/02/2009 14:25 and updated on 11/12/2019 14:17

Starting Up Notice (911-03)

Created on 26/11/2010 17:06 and updated on 10/04/2018 16:00

Starting Up Notice (914-03)

Created on 28/03/2012 16:38 and updated on 10/04/2018 16:07

Page (575-01)

• Direct reading • Construction: AISI 316 L and glass • C to C: Up to 2000 mm

Created on 11/12/2019 14:02 and updated on 11/12/2019 14:05

Category ()

Created on 23/09/2006 18:33 and updated on 27/03/2018 15:34

Page (555-01)

Capacitive, high frequency, fail-safe detection  For aggressive and conductive liquids  Positive active alarm  Auto diagnostic system and LED  Approvals: DIBT Z-65.13-294, for overfillingdetection WHG§19, and VLAREM II

Created on 13/02/2007 11:52 and updated on 10/04/2018 14:10

Starting Up Notice (446-01)

Created on 31/07/2007 14:20 and updated on 10/04/2018 15:32

Page (592-02)

Fill level monitoring in ATEX Ex area For flammable liquids No moving parts Accurate and reliable measurement Output signal 4-20 mA, 2 wires Free from fluid viscosity or conductivity Scales: up to 4000 mm ATEX certification

Created on 27/11/2009 10:59 and updated on 10/04/2018 14:22

Starting Up Notice (193-11)

Created on 27/12/2010 15:25 and updated on 10/04/2018 15:26

Page (635-02)

• Machined integral or welded • Large choice of materials • Process connections: Process: ½'', ¾''", 1" Welded fittings Flanges

Created on 11/12/2019 16:56 and updated on 11/12/2019 16:58

Starting Up Notice (364-01)

Created on 01/10/2007 16:49 and updated on 10/04/2018 15:30

News ()

We clarify the parameters of fluids turbidity... Since 2 decades, we develop the range of turbidity monitors for continuous survey or just alarming systems. Wastewater: From WWTP, sedimentation process, flocculation... Drinkable water: From spring,...

Created on 22/12/2009 14:23 and updated on 10/04/2018 16:22

Starting Up Notice (523-01)

Created on 07/07/2011 14:39 and updated on 10/04/2018 15:36

Page (131-01)

• Protection holder • Easy calibration routine • For 1 electrode (fitting PG 13.5) • Unscrewable protection end • In AISI 316 L

Created on 04/12/2019 10:53 and updated on 04/12/2019 11:03

Page (145-01)

• Chemical and mechanical cleaning • For one pH electrode PG 13.5 • Easy to install • Accessory added to the pH probe

Created on 09/10/2006 10:14 and updated on 04/12/2019 11:58

Page (543-01)

For aggressive and electrically conductive liquids Construction: PVC or PVDF Manufacture on request upon drawings Fixed alarm distances 4 contacts as a maximum

Created on 20/03/2007 18:43 and updated on 10/04/2018 14:07

Page (520-03)

Built in ballast Potential-free micro-switch High switching rating Quick and easy to install PVC or TPK cables, length 5 m, 10 m ... Built in ballast Potential-free micro-switch High switching rating Quick and easy to install PVC or TPK cables, length 5...

Created on 19/02/2008 18:00 and updated on 10/04/2018 14:01

Page (913-08)

ND 10 to ND 50 In-line pattern Pneumatic actuator Single or double acting, Position index Status NC or NO

Created on 08/12/2011 14:24 and updated on 10/04/2018 14:40

Page (216-02)

- Color touch screen - 1 Sensor input, 0/4-20 mA Display without or with measuring unit: m; cm; %; ppm; mg; g; °C; _ (none) - 1 Pt100 sensor input - 2 Outputs 0/4-20 mA (measurement & T °C) - 4 Relay outputs (thresholds, alarm and/or regulation)...

Created on 10/12/2019 13:08 and updated on 10/12/2019 13:11

Page (755-01)

Manufactured Venturi channels are dedicated for flow rate measurement in open flumes, and totalization on effluents

Created on 09/10/2006 17:26 and updated on 10/04/2018 14:27

Page (361-01)

• Cell factor K = 1 • Fitting PG 13.5 • Body: Glass tube Ø 12 mm • Platinum measuring elements

Created on 18/05/2007 10:15 and updated on 10/12/2019 15:30

Starting Up Notice (106-02)

Created on 25/11/2008 14:02 and updated on 10/04/2018 14:52

Starting Up Notice (913-06)

Created on 12/12/2011 17:36 and updated on 10/04/2018 16:04

Page (451-03)

• Dissolved oxygen measurement • Scales: 0.01 to 50 mg/l or 0 to 500 % • 1 Input for AQUAPLUS probe • 2 Analogue outputs 0/4-20mA • 4 Relay outputs (Thresholds and alarm) • OPTIONS: Extension terminal for 2nd measuring parameter

Created on 10/12/2019 16:16 and updated on 10/12/2019 16:18

Starting Up Notice (141-01)

Created on 15/06/2007 17:26 and updated on 10/04/2018 15:18

Page (556-01)

Universal use for electrically conductive, non-flammable water endangering liquids According  WHG § 19  in Germany,  the series is called MAXIMAT® C. No moving parts Process connection BSP 2", PVC, sliding Stem PEHD: Ø 40 mm Adjustable immersion...

Created on 25/03/2009 14:56 and updated on 10/04/2018 14:15

Page (190-10)

• For swimming pools • Measuring ranges Chlorine from 0.01 to 5 & 10 mg/l Isocyanuric acid from 2 to 200 mg/l pH from 6.5 to 8.4 • Delivered ready to use

Created on 06/12/2010 15:06 and updated on 04/12/2019 14:19

Starting Up Notice (914-04)

Created on 28/03/2012 16:42 and updated on 10/04/2018 16:08